Germany

← Back to catalogue

2-Piece Floating Rear Brake Rotor Upgrade Kit for Audi C7 S6/S7 034-301-2013
  • 2-Piece Floating Rear Brake Rotor Upgrade Kit for Audi C7 S6/S7 034-301-2013
  • 2-Piece Floating Rear Brake Rotor Upgrade Kit for Audi C7 S6/S7 034-301-2013
  • 2-Piece Floating Rear Brake Rotor Upgrade Kit for Audi C7 S6/S7 034-301-2013

2-Piece Floating Rear Brake Rotor Upgrade Kit for Audi C7 S6/S7

Part number: 034-301-2013

Not listed by the manufacturer for your selected vehicle: Audi S4 B8/B8.5 (2010-2016) 3.0 TFSI

€1,327.75

incl. 19% VAT, plus shipping

Delivery time: approx. 2 weeks

Motorsport product: no approval papers (ABE, parts certificate, registration) can be supplied. Fitting it may void the vehicle's type approval for road use.

Complete rear brake rotor upgrade kit in floating 2-piece design for the factory rear calipers of the Audi C7 S6/S7. Each rotor weighs approximately 6.3 kg, reducing rotating mass by about 1.5 kg per corner compared to the 7.8 kg factory rotor, while retaining sufficient thermal mass in the friction ring. 72 directionally curved vanes drive cool air forcefully through the rotor to dissipate heat.

Description

Product Description

The factory rear brake rotors on the Audi C7/C7.5 S6/S7 do not make full use of the available rotor surface. Both the top and bottom portions of the rotor face remain uncontacted by the pad, and the swept pad area itself retains 3mm of extra, unused material around its edge. The rotor ring design of this upgrade kit removes the areas not contacted by the pads, improving overall efficiency and reducing unnecessary unsprung weight. This results in a reduction of rotor diameter from 356mm to 350mm with no loss of braking force, producing a lighter rotor with improved cooling compared to the OEM part.

Weighing approximately 13.9 lbs, each rotor reduces rotating weight by about 3.3 lbs per corner compared to the 17.2 lb factory rotor. Despite this weight reduction, the rotor retains sufficient thermal mass in its ring to properly capture and dissipate heat.

The central hat is made from 6061-T6 aircraft-specification aluminum. The disc itself is manufactured from a proprietary metal alloy capable of withstanding high braking temperatures while maintaining its form under hard street use and extended track sessions. From the factory, the same rotor is used on both sides of the S6/S7, leaving one side with incorrect venting and cooling characteristics. This kit instead uses 72 directionally curved vanes, properly oriented for each side of the vehicle, to force cool air through both rotors and dissipate heat equally.

The friction face features J-slot slots that clean the pad and rotor surface of contaminants and allow hot pad outgassing, while producing less braking noise than a traditionally slotted rotor.

The floating connection between hat and rotor ring uses high-strength alloy steel bobbins. These pins carry the braking loads while maintaining axial and radial float between the hat and disc, allowing safe thermal expansion and contraction.

Features

  • Lightweight construction (13.9 lb rotor vs. 17.2 lb OE Audi rotor)
  • Floating, 2-piece design
  • Rotor diameter optimized for caliper/pad location, reduced from 356mm to 350mm overall diameter
  • Aerospace-grade aluminum hats
  • CM-250 special alloy rotor rings
  • J-slotted friction face
  • OEM fitment and functionality
  • 72 properly oriented curved vanes force cooling air through the brake disc
  • Floating bobbin mounting system
  • Replaceable rotor rings
  • Lower long-term maintenance cost

What's Included

  • 356x22mm specification left rotor, reduced to 350mm diameter
  • 356x22mm specification right rotor, reduced to 350mm diameter
  • Installation and break-in instruction sheets

OE Part Interchange

  • 4H0 615 601 L
  • 4H0 615 601 P
Weight per rotor
13.9 lb (ca. 6,3 kg)
OE rotor weight
17.2 lb (ca. 7,8 kg)
Rotor diameter (optimized)
350 mm
OE rotor diameter
356 mm
Rotor specification
356 x 22 mm
Hat material
6061-T6 Aluminium
Rotor ring material
CM-250 Speziallegierung
Number of cooling vanes
72
Shipping weight
14.4 kg

–

  • 356x22mm specification left rotor, reduced to 350mm diameter
  • 356x22mm specification right rotor, reduced to 350mm diameter
  • Installation and break-in instruction sheets
Manufacturer
034Motorsport, Inc., 42968 Osgood Rd, Fremont, CA 94553, USA, contact@034motorsport.com
Responsible person in the EU (importer)
Tij-Power, Thorsten Meier, Mühlenheide 91, 33106 Paderborn, info@tij-power.com

Matching accessories

Related products