S34 Carbon Fiber Intake, Volkswagen & Audi MQB EA888 Gen 3
Part number: 034-108-1044
€634.06
incl. 19% VAT, plus shipping
Delivery time: approx. 2 weeks
Motorsport product: no approval papers (ABE, parts certificate, registration) can be supplied. Fitting it may void the vehicle's type approval for road use.
The S34 Carbon Fiber Intake for Volkswagen and Audi 1.8T and 2.0T MQB vehicles delivers improved power, induction sound, and overall performance to the EA888 Gen 3 turbocharged four-cylinder engine in an attractive, clean, and cost-effective package. Note: This intake only fits with the GTI battery and is not compatible with AWD vehicles using the larger OE battery.
Description
Product Description
This comprehensive, performance-oriented intake system was developed for the turbocharged 1.8T and 2.0T EA888.3 engine found in the MQB generation of Audi A3/S3/TT/TTS, VW Golf/GTI/R, and Mk7 VW GLI. The S34 Carbon Fiber Intake for 8V/8V.5 Audi A3/S3/TT/TTS, Mk7/7.5 VW Golf/GTI/R, and Mk7 VW GLI, 1.8T/2.0T Gen 3, delivers measurable gains in horsepower and torque, a more aggressive induction and turbocharger sound, and a high-quality carbon fiber heat shield that keeps hot engine bay air out of the intake.
Multiple designs were modeled, prototyped, and tested throughout development to ensure measurable performance gains and excellent fitment. The result is an optimized open-airbox design that uses the factory fresh air duct to channel cool outside air to the filter. The larger airbox accommodates a large 4" inlet conical air filter without restrictive shrouding, with air then flowing through a CFD-optimized 4-ply silicone inlet hose that smoothly increases air velocity up to the throttle body.
Note: This intake only fits with the GTI battery installed. It will not fit AWD VW/Audi vehicles equipped with the larger OE battery. If your vehicle came with the larger Group 46/H6 battery, you will need to switch to the GTI battery listed below:
- GTI Battery Part Number: 5K0 915 105 C or 000 915 105 DC
- GTI Battery Size: Size H5 / Group 47, 61Ah, 330A (DIN)
Minimizing Unnecessary Filter Shrouding
A critical factor for a high-flowing intake is allowing air to flow freely around and into the filter. If airflow around the filter is restricted, flow into the filter is limited as well. Many aftermarket kits fit oversized filters into housings that can't properly accommodate them, choking the filter and reducing overall flow. Extensive testing and refinement of this design allow for maximum airflow around the filter, resulting in the right-size filter in the right-size housing - delivering maximum airflow and performance with OEM-level filtration.
Maximizing Airflow
A CFD-optimized 4-ply silicone intake tube serves as a direct, high-performance replacement for the factory plastic accordion/sound-deadening hose. Using CAD software and 3D scanning, the cross-sectional area of the intake tube was optimized within the factory space constraints. The result makes the most of the available packaging space while providing smooth transitions for optimal airflow to the throttle body.
Performance Air Filter
The S34 Carbon Fiber Intake uses a high-flow conical air filter with a double-layer pleated cotton filtration medium capable of trapping particles as small as 5 microns. The enlarged filtration surface increases flow while maintaining superior filtration. This air filter has been tested in applications exceeding 800 HP with minimal restriction and OEM-level filtering quality.
Unlike many intake kits that leave the air filter unsupported and free to move, a dedicated air filter support prevents unwanted movement while still allowing compliance for engine movement under varying load. An additional air shroud stays securely in place and does not rub against other engine bay components.
Product Features
- Developed in-house
- Fits both left- and right-hand drive configurations
- High-quality carbon fiber air block-off shield
- High-gloss epoxy finish
- 4-ply gloss black silicone intake tube
- OEM+ fit and finish
- No rubbing or excessive movement
- Dyno-proven horsepower and torque gains
- Stock intake: 226 HP, 296 TQ
- S34 open filter configuration: 235 HP, 305 TQ
- Improved airflow over factory airbox and intake tube
- Stock intake: 552.6 CFM @ 28in H2O
- S34 intake with S34 turbo inlet: 908.3 CFM @ 28in H2O, approximately 64% increase
- Enhanced engine induction sounds
- Improved throttle response
- Large 4" inlet conical pleated cotton air filter
- Reduced intake air temperature
- Secure installation using factory mounting grommets
- Simple, straightforward installation instructions
MAF Sensor Note
This product does not fit vehicles equipped with a MAF sensor. Please confirm your vehicle does not have this component before ordering.
Measurable Performance Gains
Intake performance can be quantified through pressure drop, CFM airflow, and horsepower/torque testing. The more freely air flows through the intake filter and airbox, the less the engine is restricted when drawing in air - a restrictive intake limits the power an engine can produce. Factory intakes typically perform well at stock power levels but become increasingly restrictive as power output increases.
Pressure drop and CFM can be measured precisely under controlled conditions, allowing direct comparison between intake systems. Dyno horsepower testing is more variable, as it depends on additional factors such as ECU tuning, exhaust modifications, and turbo system changes, since the intake itself does not produce power but rather supports it.
CFM Gains
CFM (cubic feet per minute) measures airflow - the higher the number, the more horsepower an intake can support. All intakes are tested at 28 inches of water on a Superflow airflow bench for accurate, repeatable results.
- Stock intake: 553 CFM @ 28" H2O
- S34 intake: 908 CFM @ 28" H2O
Pressure Drop Improvements
Pressure drop is the difference between ambient air pressure and the air pressure measured at the turbocharger inlet across the engine's rpm range. A higher pressure drop at a given rpm indicates a more restrictive intake system.
| Intake Configuration | Chart Color | Pressure Drop |
|---|---|---|
| S34 Carbon Fiber Intake | Yellow | 0 psi |
| Stock Intake | White | -1.00 psi |
Dyno-Verified Wheel Horsepower & Torque Gains
Development was validated on multiple vehicles using a Mustang AWD dynamometer to confirm substantial horsepower and torque gains with both stock and upgraded turbochargers.
Peak Wheel Horsepower & Torque with Stage 1 Software
- Stock intake: 226 WHP / 296 WTQ
- S34 Carbon Fiber Intake: 235 WHP / 305 WTQ
- Peak crank gains: 31 HP and 27 TQ @ 6,000 RPM
- Filter Micron Rating
- 5 Mikron
- Filter Inlet Diameter
- 4 Zoll
- Silicone Hose Ply Count
- 4-lagig
- Stock Airflow
- 552,6 CFM @ 28in H2O
- S34 Airflow
- 908,3 CFM @ 28in H2O
- Stock Horsepower & Torque
- 226 PS / 296 Nm
- S34 Horsepower & Torque
- 235 PS / 305 Nm
- S34 Pressure Drop
- 0 psi
- Stock Pressure Drop
- -1,00 psi
- Shipping weight
- 4.6 kg
–
Audi (9)
Seat (5)
- Carbon fiber heat shield
- 4" inlet silicone hose
- 4" double-layered cotton pleated filter
- Secondary air injector adapter
- Secondary air injector filter
- Metal mounting bracket for intake hose
- Manufacturer
- 034Motorsport, Inc., 42968 Osgood Rd, Fremont, CA 94553, USA, contact@034motorsport.com
- Responsible person in the EU (importer)
- Tij-Power, Thorsten Meier, Mühlenheide 91, 33106 Paderborn, info@tij-power.com
Matching accessories
R460 Hybrid Turbocharger System for 8V Audi S3 & MkVII Volkswagen Golf R 2.0 TFSI (MQB)034-145-1017€6,766.52
Dynamic+ Lowering Springs for MkVII Volkswagen Golf R034-404-1004€396.73
Billet Spherical Dogbone Mount Performance Pack with Dogbone Pucks, Volkswagen & Audi MQB And MQB EVO With Manual Or 6-Speed DSG034-509-1041€578.08



















